Skip to main content

How to Use Limecote™ Lime Plaster

This is how to use lime plaster on an old wall, our full method for Limecote™, from an empty bucket to a wall that's ready to paint. It's the same whether you're patching a few square feet or skim coating a whole room: prepare the wall, mix, put it on, let it dry. Where your wall needs a closer look, we say so, and our team will talk it through with you.

Before You Start

You don't need much:

  • Limecote™, in 55 lb (25 kg) bags
  • Clean water
  • A mixing bucket
  • A mixing paddle on a drill
  • A flexible steel or plastic trowel, or a flexible skimming blade (a wide, thin blade for spreading and smoothing thin coats)
  • A water mister or spray bottle
  • Gloves and eye protection

As a guide, one bag covers about 27 sq ft (2.5 m²) at 5/16 inch (8 mm) thick. For other thicknesses, put your wall into the calculator:

How Many Bags Do I Need?

Based on about 5.3 gallons (20 L) of plaster per bag. A guide only.

Prepare the Wall

The wall needs to be clean and free of loose, crumbly material. On solid walls that haven't been primed, such as brick, stone or old lime plaster, dampen the surface lightly with the mister first. That settles the dust and slows how fast the wall draws water out of the fresh plaster, so the plaster bonds better. Never plaster onto a wall with water sitting on the surface: the water stops it sticking.

Some surfaces need more:

  • Drywall: tape the joints with fiberglass or paper tape first, because that's where a crack is most likely to start, then prime it with a grit primer such as MAPEI Eco Prim Grip or Eco Prim Grip Plus. Drywall is paper-faced gypsum, made for thin, fast-setting gypsum coats, and a heavier lime plaster that dries more slowly can soften the board, lift the paper or warp it. The primer gives the plaster something to grip and keeps the moisture out of the board.
  • Painted walls: prime them, as long as the paint is sound. The plaster is only as good as the wall behind it, so if the paint isn't firmly stuck, the plaster won't be either.
  • Existing gypsum plaster: prime it before you skim. The primer controls how fast the wall pulls water out of the plaster, which gives you longer to get a good finish. Houses from about 1900 to 1940 may have lime, or lime and gypsum, so if you can't tell which you've got, ask us.
  • Old lime plaster: remove anything loose, crumbly or dusty, wash off calcimine (old soft paint) or whitewash, then dampen it lightly.
  • Concrete block (CMU): fill the mortar joints flush with the face of the block where you can, rather than leaving them raked back, then put on an even coat of Limecote™. The plaster then stays an even depth, and the joints are far less likely to show through in low, angled light.
  • Blueboard (gypsum veneer base): prime it with a grit or mineral primer first, as you would drywall.
  • Wood and metal lath: see Plastering Wood Lath below.

For the full list, see which surfaces Limecote™ goes on.

How to Mix Lime Plaster

  1. Pour no more than 2.6 gallons (10 L) of clean water into the bucket.
  2. Add Limecote™ gradually with the mixing paddle, never all at once.
  3. Bring it up to the consistency you want, adding more water if you need it.
  4. Once it's evenly mixed, gently add the fibers from the small bag inside.
  5. Mix thoroughly and use it right away, with no standing time.

Start low on water, because you can always add more, but you can't take it out.

There's no right or wrong amount of water. Mix it thin enough to spray or skim, or thick enough to shape by hand like modeling clay.

Limecote™ only hardens in the air, so mixed plaster kept in a covered bucket stays workable for weeks.

This video is hosted by YouTube, which may set cookies.

Watch on YouTube

Putting It on the Wall

With the fibers mixed in, Limecote™ doesn't shrink, so it shouldn't crack. Coats of 1 inch (25 mm) go on easily, and you can fill hollows of about 4 inches (100 mm) or more in one pass. For deep hollows, a stiffer mix with less water helps. Take care with thick coats on a sloping surface, where they can slump, and build those up in thinner coats. Over old lime plaster, work the other way: thin passes, not one heavy coat.

The flexible trowel or skimming blade on your list does almost all of it. Once you've got a finish you're happy with, that's it. There's no tending to it afterward.

If bubbles or blisters show on the final coat, leave them until the next day, then smooth them out, with a light mist of water if it needs it.

Plastering Wood Lath

When old lath and plaster fails, it has virtually always sheared at the small neck of plaster that passes between the laths, usually because the animal hair reinforcing it was missing or had degraded. So the first coat has two jobs: get plaster through the gaps, and keep it joined to the plaster in front.

Limecote™ makes its own first coat:

  1. Push the first pass well through the lath so it curls behind and forms a key (the plaster pushed through the lath that holds the wall on).
  2. Build it up to at least 3/8 inch (10 mm) over the face of the lath.
  3. Flatten it along the line of the lath, not across it.
  4. Scratch the surface. This is your scratch coat: a coat scored with lines so the next one has something to grip.
  5. Once it's firm but not yet dry, apply a 5/16 inch (8 mm) finish coat.

Metal lath takes Limecote™ too, but talk to us about its first coat.

Where old plaster has come loose from the lath, talk to us about that wall before you start.

Straw Bale and Earth Walls

On straw bale, you can spray Limecote™ with a small hopper gun and a 3 hp shop compressor. Spray the first coat quite liquid and well into the straw as a scratch coat, and let it harden before the second coat. Limecote™ doesn't mind changes in depth, so you can fill low spots by lingering a little longer with the spray. That also means the hollows decide how many bags you use, so ask us before you order for a big wall.

Adobe, cob, clay lump, daub and clay block take Limecote™ as well.

Letting It Dry

We don't give drying times, or times between coats, because every job dries at its own speed, depending on the temperature and humidity in the room.

Limecote™ is non-hydraulic, so it hardens slowly by taking carbon dioxide from the air. Before you paint or paper it, though, it just needs to be dry.

It gets noticeably lighter in color as it dries. Judge it by the coldest, darkest, dampest section near the bottom of the wall: once that has turned lighter, you're ready.

Unlike most lime plasters, Limecote™ doesn't mind being helped along. A space heater and a dehumidifier are fine to use and will cut the drying time a great deal. Put the heat into the room, not straight onto the wall.

Painting or Papering It

Once it's dry, limewash, clay paint, mineral paint and ordinary latex paint can all go over Limecote™. Choose by what you want from the wall. If it's an eco finish, there'll be a sustainable option. If you want moisture to keep passing through the wall as vapor and drying out, ask the paint maker how vapor permeable their paint is.

To paper it, cross-line first: hang lining paper horizontally, then your wallpaper over it. Wallpaper shrinks as the seams dry, and over worked plaster that can pull the seams open. Don't use vinyl paper. Ask us which paste to use.

Working Outside

Limecote™ works indoors anywhere in the US. Outside, it's what Americans call lime stucco or exterior lime plaster, and the climate matters. Limecote™ is non-hydraulic, so it needs air to harden, and where winters bring a lot of freeze-thaw cycles it's very hard for it to harden fully. It suits drier states with mild to hot weather, such as California, Arizona, New Mexico, southern Colorado and western Texas, and Oregon and Washington, whose climate is close to ours in England. Anywhere, covered spots like porches or walls under deep eaves are a good fit. Exterior work is a job for a plasterer who knows lime, so talk to us about yours first.

Stop work when it's 41°F (5°C) and falling. Frost is the risk: water in wet plaster expands by 9% as it freezes, and that breaks the plaster apart. Heat won't harm it, but it makes the drying harder to control. For cold weather, read our winter working guide.

Storage and Safety

Kept dry and frost free, Limecote™ has no expiration date.

Calcium hydroxide is an irritant. It causes serious eye damage and skin irritation, and may cause respiratory irritation. Wear protective gloves, eye and face protection, and avoid breathing dust. If it gets in your eyes, rinse cautiously with water for several minutes and immediately call for medical advice. Keep it out of reach of children. The full detail is in the safety data sheet, a UK document, on Technical Downloads.

Stuck? Ask the People Who Make It

No question is too basic. If your wall isn't covered here, or you'd like to talk your plan through first, email [email protected] or send us a question. The people who make Limecote™ are the ones who answer, and we'll get back to you within one business day. Plenty of answers are already on our frequently asked questions page.