Lime Plaster FAQs
These are the lime plaster questions we're asked most by people working on older American houses. Open the one you need, and if yours isn't here, ask us at the bottom of the page.
Lime and Limecote™
Which Lime Is Limecote™?
Limecote™ is a non-hydraulic lime plaster: it hardens by taking carbon dioxide from the air, not by reacting with water.
We make it from East Anglian chalk and Derbyshire lime and sell it dry in a 55 lb (25 kg) bag, with the fibers inside. It contains no gypsum, cement or pozzolans (the additives that make some limes set like cement).
What's the Difference Between Hydraulic and Non-Hydraulic Lime?
Hydraulic lime sets partly by reacting with water, while non-hydraulic lime hardens only by taking carbon dioxide back from the air.
Clay, silica and alumina in a hydraulic lime cause that reaction. Non-hydraulic limes such as Limecote™ contain none of them. Current thinking is that hydraulic lime is generally too strong, and lets less moisture pass through as vapor than non-hydraulic lime does.
Is Limecote™ the Same as Type S or Hydrated Lime From a Hardware Store?
No: Type S is hydrated lime you mix with sand yourself, while Limecote™ is a non-hydraulic lime plaster sold dry, with the fibers in the bag.
Is My Old Plaster Lime or Gypsum?
If your house was built before about 1900, it's most likely lime; from about 1900 to 1940, it may be lime, or lime and gypsum.
The National Park Service's Preservation Brief 21 on historic flat plaster says: "Until the end of the 19th century, plasterers used lime plaster."
If you can't tell which you've got, ask us. Old lime plaster is cleaned and lightly dampened before a skim coat, while gypsum plaster is primed first.
Do I Need Lime Plaster, or Will Gypsum Plaster or Joint Compound Do?
On a lime-plastered wall, we'd repair with lime, not gypsum plaster or joint compound.
Lime lets moisture pass through the wall as vapor and dry out, where a hard skin would trap it. The National Park Service's Preservation Brief 21 notes that gypsum plaster "was more vulnerable to water damage than lime," and that "In general, gypsum plaster is the material plasterers use today."
Will It Crack?
It shouldn't: with the fibers mixed in, Limecote™ doesn't shrink.
Every bag carries 5.3 oz (150 g) of fine man-made fiber, about 280 miles of it. We use it in place of animal hair, because when old lath and plaster fails, missing or decayed hair is by far the most common cause.
Is Limecote™ Fire Rated?
Yes, Limecote™ is Class A1 fire rated under the European classification, tested to the international standards ISO 1182 and ISO 1716.
Those tests should map to their American equivalents for non-combustible materials, but Limecote™ hasn't been fire tested in the US yet. The certificate is on our technical downloads page.
Walls and Surfaces
Can You Put Lime Plaster Over Drywall?
Yes, Limecote™ goes over drywall once it's primed with a grit primer such as MAPEI Eco Prim Grip or Eco Prim Grip Plus.
Drywall is paper-faced gypsum, so the water in a heavier, slower-drying lime coat can soften it, lift the paper or warp the board. The primer keeps the water out of the board and gives the plaster something to grip. Tape the joints with fiberglass or paper tape before you prime, because the joints are where a crack is most likely to start. See every surface in the surface table on the Limecote™ page.
Can It Go Over Painted Walls or Existing Gypsum Plaster?
Yes to both, once they're primed.
Paint has to be sound: the plaster holds no better than the paint underneath it. On gypsum plaster, the primer controls suction, meaning how fast the wall pulls water out of the plaster, so you have longer to finish.
Can I Use It on Wood Lath or Metal Lath?
Yes to both, and on wood lath Limecote™ makes its own first coat.
Press the first pass through so it curls behind the lath and forms a key, the plaster that holds the wall on. Take it to at least 3/8 inch (10 mm) over the lath face, flatten along the lath rather than across, and scratch it. When it's firm but not yet dry, put on a 5/16 inch (8 mm) finish coat.
Metal lath works too, but talk to us about its first coat.
What About Blueboard, Concrete Block or Old Cement Stucco?
Blueboard and concrete block are fine with the right preparation, and we take old cement stucco case by case.
- Blueboard: the gypsum board made for a thin coat of veneer plaster. Prime it with a grit or mineral primer first, as you would drywall.
- Concrete block (CMU): fill the mortar joints flush where you can, then put on an even coat, so the plaster sits at an even depth and the joints don't show through in low, angled light.
- Cement stucco: ask us first. Limecote™ finishes smooth, so it may not match a textured old finish.
Can I Skim Coat Over Old Lime Plaster?
Yes, a Limecote™ skim coat gives old lime plaster a new finish and keeps the historic plaster in place.
Clear off anything loose, crumbly or dusty, and wash away powdery calcimine (old soft paint) or whitewash. Mist the wall lightly to settle the dust and slow how fast it pulls water from the new coat, but never plaster onto standing water. Apply it in thin passes.
Does It Work on Straw Bale, Adobe and Cob?
Yes, Limecote™ works on straw bale, adobe, cob, clay lump, daub and clay block.
On straw bale, spray it with a small hopper gun and a 3 hp shop compressor: a quite liquid first coat worked well into the straw, then a second coat once that has hardened.
Which Mesh Should I Use?
Use a mesh with 3/8 inch (10 mm) holes.
That's the size we sell alongside our plasters in England. Limecote™ is the one product of ours sold in the US, so buy mesh from a building supply yard and check the hole size before you do.
Mixing and Applying
How Much Water Do I Add, and When Do the Fibers Go In?
Start with no more than 2.6 gallons (10 L) of clean water, and add the fibers last.
Pour in Limecote™ gradually as you mix with a paddle, and top up the water as needed. Once it's evenly mixed, gently stir in the fibers from the small bag inside and mix thoroughly. See our guide to using Limecote™.
How Many Bags of Limecote™ Do I Need?
One 55 lb (25 kg) bag covers about 27 sq ft (2.5 m²) at 5/16 inch (8 mm) thick.
Each bag makes about 5.3 gallons (20 L) of mixed plaster, so coverage runs from about 43 sq ft (4 m²) at 3/16 inch (5 mm) to about 11 sq ft (1 m²) at 13/16 inch (20 mm). For your wall, use the bag calculator on the Limecote™ page.
How Thick Can I Put It On?
Limecote™ goes on easily in coats of 1 inch (25 mm), and it can fill hollows of about 4 inches (100 mm) or more in one pass.
The fibers make that possible: with them mixed in, the plaster doesn't shrink. Take care with thick coats on a sloping surface, where they can slump, and build those up in thinner coats.
Can a Beginner Use Limecote™?
Yes, small repairs and skim coats are well within reach of a careful beginner.
There's no right or wrong amount of water and no standing time, and our UK customers often mention how easy it is. Bigger jobs, and all exterior work, are best done with a plasterer. Start with our step-by-step guide and mixing video.
What Do I Do About Bubbles or Blisters on the Final Coat?
Leave them overnight, then come back the next day and smooth them out, with a light mist of water if the surface needs it.
Use the same flexible steel or plastic trowel, or flexible skimming blade, that you finished the coat with.
Drying and Decorating
How Long Does Lime Plaster Take to Dry, and Can I Speed It Up?
There's no set time: Limecote™ is ready to paint or paper once it's dry, and that depends on the temperature and humidity.
It turns noticeably lighter as it dries, so go by the coldest, darkest, dampest patch near the bottom of the wall.
Unlike most lime plasters, Limecote™ can be dried faster: a space heater and dehumidifier cut the drying time a great deal. Heat the room, not the wall.
When Can I Paint It, and What Paint Should I Use?
Paint it once it's dry, with limewash, clay paint, mineral paint or ordinary latex paint.
There's a sustainable option for an eco finish, and if you want moisture to keep escaping through the wall as vapor, ask the paint maker how vapor permeable their paint is.
Can I Hang Wallpaper on Limecote™?
Yes, once it's dry, but hang lining paper first, horizontally, and don't use vinyl wallpaper.
As wallpaper dries, the paper shrinks at the seams, and areas of well-worked plaster can push through and open them up. Lining paper hung across the wall stops that. Use a ready-mixed wallpaper paste.
Weather and Outdoor Work
Can I Use Limecote™ Outside?
Yes, Limecote™ is made for interior and exterior use, and outside it's what Americans call lime stucco or exterior lime plaster.
Indoors, it works anywhere in the US. Outside, it suits drier states with mild to hot weather, such as California, Arizona, New Mexico, southern Colorado and western Texas, and Oregon and Washington, whose climate is close to ours in England. It's much harder where winters bring a lot of freeze-thaw cycles, because Limecote™ is non-hydraulic and needs air to harden fully. Anywhere, covered spots like porches or walls under deep eaves are a good fit.
Hire a plasterer who knows lime for outside work, and talk to us before you plan it.
Can I Work With It in Cold, Hot or Humid Weather?
Yes, within limits: stop work when it's 41°F (5°C) and falling, and expect heat to make the drying harder to control.
Frost is the danger: water in saturated plaster expands as it freezes and breaks the plaster apart. Read our winter working guide before any cold-weather job.
Heat does Limecote™ no harm. Indoors, a space heater and a dehumidifier put the room's warmth and humidity in your hands.
Buying, Shipping and Help
Where Can I Buy Limecote™ in the US, and How Much Does It Cost?
Limecote™ is held in stock in the US by Wood, Stone & Steel in New Jersey, at $87.50 to $92.50 a bag depending on how many you buy, plus shipping, handling and tax.
Shipping a single bag usually costs about $80 to $120, depending on where you are, and pickup is available in the New York City metro area. Contact us and we'll put you in touch, and we'll reply within one business day. See our where to buy page.
Does Limecote™ Expire, and Can I Keep Mixed Plaster for Later?
No: kept dry and frost free, an unopened bag of Limecote™ has no expiration date.
Mixed plaster keeps too. Limecote™ needs air to harden, so a batch in a covered bucket stays workable for weeks. Use some now and the rest another day.
Where Are the Data Sheet and Safety Data Sheet?
Both are on our technical downloads page, and both are UK documents.
You'll also find the UKCA declaration (the UK's product marking) and the fire certificate. Limecote™ contains calcium hydroxide, an irritant, so wear gloves and eye protection when you mix and apply it.
How Do I Reach You, and How Fast Will You Reply?
Email [email protected] or use our contact form, and we'll get back to you within one business day.
We answer by email rather than phone, from our office in Suffolk, England.
Still Have a Question?
No question is too basic, and the answer comes from the people who make Limecote™. Ask us a question or email [email protected].