Skip to main content
Limecote™

Lime Plaster, Just Add Water: Limecote™

A dry bagged lime plaster with the fibers already in the bag. Add water, mix and use it right away, on old walls and new.

  • Just Add Water
  • Fibers Included
  • Use It Right Away
  • Non-Hydraulic Lime
  • Interior and Exterior
  • Made From Chalk and Lime

Limecote™ lime plaster, 55 lb (25 kg) bag

$87.50 to $92.50 a bag, depending on how many you buy, plus shipping, handling and tax

Ask us a question

Held in stock in the US by Wood, Stone & Steel in New Jersey. Contact us and we'll put you in touch. See Where to Buy.

Ask us about delivery to your area. Pickup is available in the New York City metro area.

What Limecote™ Is and Who It's For

Limecote™ is a non-hydraulic lime plaster sold as a dry 55 lb (25 kg) bag with fibers included: add water, mix, and use it right away. It's for repairing and skim coating (a thin finishing coat over an existing wall) old plaster walls, and for plastering wood lath (the thin wooden strips old plaster was pushed onto), brick and stone.

Most people who buy it are looking after an older house. It stays flexible: it's designed to cope with the movement of a freshly cut oak frame in England, which can shrink as much as 3/4 inch across an 8 by 8 inch beam as it dries. Older American houses move too, with the wind, the seasons and the ground beneath them.

Natural builders use it on straw bale, adobe, cob, clay lump and daub. And if you want the soft look of lime plaster in a newer room, it goes over drywall once the joints are taped and the board is primed with a grit primer such as MAPEI Eco Prim Grip.

There's no right or wrong amount of water: mix it thin enough to spray or skim a fine finish coat, or thick enough to shape by hand into raised relief, like modeling clay, from the same bag.

Which Lime Is Limecote™?

Limecote™ is a non-hydraulic lime plaster, which means it hardens by taking carbon dioxide from the air rather than reacting with water. We make it from chalk and lime and sell it dry, with the fibers already in the bag, so you just add water and mix. There's no gypsum, no cement and no pozzolans (the additives that make some limes set like cement) in it.

It isn't natural hydraulic lime (NHL), it isn't lime putty in a pail, and it isn't a raw bag of lime you age yourself. It isn't the Type S hydrated lime sold in American hardware stores either.

Because it only hardens in the air, mixed plaster left in a covered bucket stays workable for weeks. Hydraulic lime is different: clay and silica in the lime make it react with water for the first part of its set.

Where You Can Use It

We have yet to find a surface Limecote™ won't stick to, but some need preparation first, and there are a few we'd like to hear about before you start.

ConfirmedAsk Us FirstNot Suitable
BrickExisting cement stuccoWe haven't found one yet. If you're unsure, ask us.
Stone, including rubble and flintHempcrete
Concrete block (CMU), with the joints filled flushCement board and poured concrete
Wood lath, with Limecote™ as its own first coat
Metal lath
Straw bale, sprayed or by hand
Adobe
Cob, clay lump, daub and clay block (earth walls)
Old lime plaster, as a skim coat
Existing gypsum plaster, once primed
Painted walls, once primed, if the paint is sound
Drywall, once taped and primed with a grit primer such as MAPEI Eco Prim Grip
Blueboard (gypsum veneer base), once primed with a grit or mineral primer
Wood fiber board and wood wool board
  • Drywall: drywall is paper-faced gypsum, made for thin coats of fast-setting gypsum plaster. A heavier lime plaster that dries more slowly can soften the board, lift the paper or warp it. A grit primer such as MAPEI Eco Prim Grip or Eco Prim Grip Plus gives the plaster something to grip and keeps the moisture out of the board. Tape the joints with fiberglass or paper tape before anything else, because the joints are where a crack is most likely to start.
  • Blueboard: prime it with a grit or mineral primer first, as you would drywall.
  • Painted walls: prime them first. The plaster is only as good as the wall behind it, so if the paint isn't firmly stuck to the wall, the plaster won't be either.
  • Existing gypsum plaster: prime it before a Limecote™ skim. The primer controls the suction, which gives you longer to get a good finish.
  • Wood lath: Limecote™ makes its own first coat. Push the first pass well through the lath so it curls behind and forms a key, then build it to at least 3/8 inch (10 mm) over the face of the lath. Flatten it along the line of the lath, not across, and scratch the surface. Once it's firm but not dry, apply a 5/16 inch (8 mm) finish coat.
  • Concrete block (CMU): if you can, fill the mortar joints flush with the face of the block rather than leaving them raked back, then put on an even coat of Limecote™. The plaster then stays an even depth, and the joints are far less likely to show through in low, angled light once it's finished.
  • Existing cement stucco: we take these case by case, especially where historic stucco needs conserving or patching. Limecote™ finishes smooth, so it may not match a textured old finish.
  • Old lime plaster: remove loose, crumbly and dusty material, wash off soft powdery calcimine (old soft paint) or whitewash, dampen the wall lightly, then apply in thin passes.

Not sure about your wall? Ask us.

How Many Bags You Need

Each 55 lb (25 kg) bag of Limecote™ makes about 5.3 gallons (20 L) of mixed plaster. How far that goes depends on how thick you put it on:

ThicknessCoverage per 55 lb (25 kg) bag
3/16 in (5 mm)About 43 sq ft (4 m²)
5/16 in (8 mm)About 27 sq ft (2.5 m²)
3/8 in (10 mm)About 21 sq ft (2 m²)
9/16 in (15 mm)About 14 sq ft (1.3 m²)
13/16 in (20 mm)About 11 sq ft (1 m²)

A guide only. Ask us about your wall, especially for deep hollows or straw bale.

How Many Bags Do I Need?

Based on about 5.3 gallons (20 L) of plaster per bag. A guide only.

Usage

How to Mix and Apply Limecote™

The full method, step by step, is on How to Use Limecote™.

Mixing. Pour no more than 2.6 gallons (10 L) of clean water into a mixing bucket. Add Limecote™ gradually with a mixing paddle, not all at once, and bring it up to the consistency you want, adding more water if you need it. Thin it for spraying, or keep it thick enough to shape by hand.

Fibers. The fibers always go in last: water first, then Limecote™, then the fibers from the small bag inside. Once the plaster is evenly mixed, add them gently and mix thoroughly. It's ready to use right away, with no standing time.

Preparing the wall. Make sure it's clean and free from loose, crumbly material. On solid walls that haven't been primed, dampen it lightly first: that settles the dust and cuts the suction, so the plaster bonds better. Never plaster onto a wall with water sitting on the surface, because the water stops it sticking.

Applying it. Use a flexible steel or plastic trowel, or a flexible skimming blade. With the fibers mixed in, Limecote™ doesn't shrink, so it shouldn't crack. It goes on easily in coats of 1 inch (25 mm), and it can fill hollows of about 4 inches (100 mm) or more in one pass. Take care with thick coats on a sloping surface, though, where they can slump: build those up in thinner coats. On wood lath, it's two coats: see the method above.

If bubbles or blisters show on the final coat, leave them until the next day, then smooth them out with a light mist of water if needed.

Drying. Limecote™ is non-hydraulic, so it hardens slowly by taking in carbon dioxide from the air. Before you decorate, it just needs to be dry, and how fast that happens depends on the temperature and humidity, inside or out. Every job dries at its own speed, so we don't give a time. Limecote™ gets noticeably lighter in color as it dries, so judge it by the coldest, darkest, dampest section near the bottom of the wall.

Unlike most lime plasters, Limecote™ can stand being helped along. A space heater and a dehumidifier, to control the warmth and humidity in the room, are fine to use and will cut the drying time a great deal.

Paint. Limewash, clay paint, mineral paint and ordinary latex paint can all go over Limecote™ once it's dry. Choose by what you want from the wall. If it's an eco finish, there'll be a sustainable option. If it's breathability, ask the paint maker how vapor permeable their paint is.

Straw bale. You can spray Limecote™ with a small hopper gun and a 3 hp shop compressor. Spray the first coat quite liquid and well into the straw as a scratch coat, let it harden, then apply a second coat.

Watch how to mix it.

This video is hosted by YouTube, which may set cookies.

Watch on YouTube

Wear gloves and eye protection; see the safety advice in the Technical and Safety tab.

Using It Outside

Limecote™ works indoors anywhere in the US. Outside, it's what Americans call lime stucco or exterior lime plaster, and the climate matters. Because Limecote™ is non-hydraulic, it hardens by taking in carbon dioxide from the air, and where winters bring a lot of freeze-thaw cycles it's very hard for it to harden fully.

It suits drier states with mild to hot weather, such as California, Arizona, New Mexico, southern Colorado and western Texas, and Oregon and Washington, whose climate is close to ours in England. Anywhere in the country, it does well outside in covered spots like porches or under deep eaves. Exterior work is a job for a plasterer who knows lime, so talk to us before you plan it.

Stop work when it's 41°F (5°C) and falling. Heat won't harm the plaster, but it makes the drying harder to control.

For general advice on lime in cold weather, see our winter working guide.

Technical and Safety

Technical Documents and Safety

These are our UK documents. If you need anything else for a US project, ask us.

All our documents are also on Technical Downloads.

Fire. Limecote™ is Class A1 fire rated under the European classification, tested to the international standards ISO 1182 and ISO 1716. Those tests should map to the US standards for non-combustible materials, but Limecote™ hasn't been fire tested in the US yet.

What's in the bag. Non-hydraulic lime plaster made from East Anglian chalk and Derbyshire lime, plus 5.3 oz (150 g) of fine man-made fiber, which works out at about 280 miles of reinforcement per bag. No gypsum, cement or pozzolans. It comes packed in a recyclable LDPE bag.

Storage. Kept dry and frost free, it has no expiration date.

Safety

  • Caution: Calcium Hydroxide is an irritant.
  • Causes serious eye damage
  • Causes skin irritation
  • May cause respiratory irritation
  • Keep out of reach of children
  • Wear protective gloves, eye and face protection
  • If in eyes, rinse cautiously with water for several minutes and immediately call for medical advice
  • If on skin, wash with plenty of soap and water
  • Avoid breathing dust. If inhaled, remove the affected individual to fresh air and keep at rest in a position comfortable for breathing
Shipping and Where to Buy

Buying Limecote™ in the US

We make Limecote™ ourselves in Suffolk, England. Being dry bagged, it's simple to transport and store.

  • Where to buy: held in stock in the US by Wood, Stone & Steel in New Jersey. Contact us and we'll put you in touch.
  • Price: $92.50 a bag for 1 to 10 bags, $90 a bag for 10 to 40 bags, and $87.50 a bag for a full 40-bag pallet, plus shipping, handling and tax.
  • Delivery: shipping a single bag usually costs about $80 to $120, depending on where you are, which covers boxing, labeling and shipping. Pickup is available in the New York City metro area. Ask us about delivery to your area.

Every inquiry comes straight to us at Best of Lime. Email [email protected] or send us a question, and we'll get back to you within one business day.

Where It Comes From

If your house was built before about 1900, its walls were most likely plastered with lime. The National Park Service's Preservation Brief 21, Repairing Historic Flat Plaster says so plainly: "Until the end of the 19th century, plasterers used lime plaster." In houses from about 1900 to 1940, you're likely to find lime, or lime and gypsum.

Limecote™ is based on a lost medieval English recipe, and plaster of this kind is still found on buildings five centuries on. That's no accident. On timber framed buildings, especially green oak (freshly cut oak that is still drying), the frame can move a great deal as the timber dries out. Rigid, heavy sand-based mixes couldn't cope and failed, which is why the old recipe stayed flexible.

We've been making lime plaster in Suffolk since 2014, from East Anglian chalk and Derbyshire lime. Read more about the people who make it.

Frequently Asked Questions

Where Can I Buy Limecote™ in the US, and What Does Shipping Cost?

Limecote™ is held in stock in the US by Wood, Stone & Steel in New Jersey, with pickup in the New York City metro area. Contact us and we'll put you in touch. It's $87.50 to $92.50 a bag, depending on how many you buy, plus shipping, handling and tax. Shipping a single bag usually costs about $80 to $120, depending on where you are. More on Where to Buy.

Do I Need Lime Plaster, or Will Gypsum Plaster or Joint Compound Do?

It depends on your house. The National Park Service's Preservation Brief 21 notes: "Until the end of the 19th century, plasterers used lime plaster." If your walls are older than that, lime is the original material. The same brief says gypsum plaster "was more vulnerable to water damage than lime." Lime also lets moisture pass through the wall as vapor and dry out, and Limecote™ is made to move with a timber frame as it dries and settles.

Is Limecote™ the Same as Type S or Hydrated Lime From a Hardware Store?

No. Limecote™ is a non-hydraulic lime plaster: it hardens by taking carbon dioxide from the air, and comes as a dry premix of chalk and lime with the fibers in the bag, so you just add water. It contains no gypsum, cement or pozzolans. Type S is a hydrated lime you mix with sand yourself, and most of it is dolomitic, part calcium and part magnesium. If you're comparing it with a lime you already have, ask us and we'll talk it through.

Can I Put Limecote™ Over Drywall?

Yes, once the joints are taped and the drywall is primed with a grit primer such as MAPEI Eco Prim Grip, so the paper face doesn't soften or lift under the wet plaster. It's a good way to get the soft look of lime plaster in a newer room. Painted walls, existing gypsum plaster and blueboard need priming too.

Will It Crack?

With the fibers mixed in, Limecote™ doesn't shrink, so it shouldn't crack. Every bag carries 5.3 oz (150 g) of fine fiber, about 280 miles of it, and the fibers always go in last, after the plaster is mixed. On wood lath, Limecote™ makes its own first coat, pushed well through the lath and scratched before the finish coat goes on.

How Long Before I Can Paint It?

When it's dry, and that depends on the temperature and humidity in the room, so every job is different. You'll see it turn noticeably lighter as it dries. Unlike most lime plasters, Limecote™ can be helped along with a space heater and a dehumidifier. Once it's dry, limewash, clay paint, mineral paint and ordinary latex paint can all go over it.

Can a Beginner Use It?

Small repairs and skim coats are well within reach. There's no right or wrong amount of water, no standing time, a mixing video to follow, and a team that answers questions. Reviews from our UK customers often say how easy it is for a first-timer. Bigger jobs, and all exterior work, are best done with a plasterer. See How to Use Limecote™ and our frequently asked questions for more.

Talk to the People Who Make It

Claire Stokes, Company Manager at Best of Lime

Claire Stokes, our Company Manager, runs the office, and the team here make every bag. Don't see your question listed? Ask us about your wall or your project, and we'll get back to you within one business day.

Ask us a question or email [email protected].